Skip to main content

Is your Wii power supply broken?

I just got a brand new 40" LCD TV (which, by the way, is awesome) this morning and started testing it out. First the PC, then the Xbox 360, then the PlayStation, and finally I tried turning on my Wii and nothing happened. No lights, no sounds, nothing.

So, I started troubleshooting:
  • Check the connections to the Wii; looks good.
  • Change the surge protector socket it's plugged into; no change.
  • Reset the surge protector; still nothing.
  • Measured the voltage in the socket (any excuse to use my fancy new volt meter); a solid 110V.
  • Measured the voltage from the power supply; a solid 0V. Bingo.
At this point I was releived to find that my Wii was most likely not dead. This evening I started looking into repairing power supplies. I found a couple sites that gave me hope, so I decided to crack it open and see what I could find. That's when I discovered that my BX-100 bit set was missing the appropriate bit for the screws Nintendo used. Flabergasted, I found Chris Meyer's site which suggest just using needle-nose pliers. I found that wire snips actually worked best since I could grip the dimples easily with the sharp edges. The hardest part was actually popping apart the plastic pieces (I suggest a butter knife or a metal plaster spatula/scraper).

However, what's more interesting than his instructions are his results. He and I both found nothing wrong, put the brick back together, and then discovered it was magically working again. This could be a coincidence, but I think it's more likely that simply leaving the power supply unplugged for long enough allows it to reset.

With that, here is my suggestion if you find that your own Wii power supply has suddenly stopped working: before you tear it up trying to fix it, just unplug it and go outside to play instead. Maybe when you come back, it will love you again.

Popular posts from this blog

Email Injection

Not so long ago, I ran a wiki called SecurePHP. On that wiki, there was one particular article about email injection that received a lot of attention. Naturally, with all the attention came lots of spam. As a result, I disabled editing of the wiki and content stagnated. Still, the email injection article remained popular. About a year later, the server that hosted SecurePHP died and I never had a chance to hook it all back up. I saved the article though and I'm reposting it now. It may be a bit old (I've been away from PHP for a long time), and I didn't write all of it, so feel free to leave comments about needed updates and corrections. Though this article focuses on PHP, it provides a lot of general information regarding email injection attacks. The PHP mail() Function There are a lot of ways to send anonymous emails, some use it to mass mail, some use it to spoof identity, and some (a few) use it to send email anonymously. Usually a web mailform using the mail() funct
Read more

XBee ZNet 2.5 Wireless Accelerometer

I managed to put together a wireless accelerometer the other night using my two new XBees, an Arduino XBee shield, an XBee Explorer USB, an ADXL330, and some Python. I struggled a bit with some of it, so here's what I learned: First, a parts list. XBee 2mW Series 2.5 Chip Antenna Arduino XBee (with XBee Series 2.5 module) XBee Explorer USB ADXL330 I'm not sure exactly what the specs are on the XBee that comes with the Arduino shield. But, it is definitely a series 2.5. The first thing to do is to configure and upgrade the firmware on your XBees. To do that, you'll need X-CTU (for the firmware upgrade at least, but it's also nice for configuration) which, unfortunately, is only available for Windows. But, it works fine from VMware. First up, the XBee we'll hook up to the computer to read incoming data from the accelerometer: Plug one of the XBees into the Explorer (it's also possible to do this from the Arduino shield by shifting the two XBee/USB jumpers to USB
Read more

Android Recipes and Snippets

I've put together a small collection of Android recipes. For each of these recipes, this is an instance of Context (more specifically, Activity or Service ) unless otherwise noted. Enjoy :) Intents One of the coolest things about Android is Intents . The two most common uses of Intents are starting an Activity (open an email, contact, etc.) and starting an Activity for a result (scan a barcode, take a picture to attach to an email, etc.). Intents are specified primarily using action strings and URIs. Here are some things you can do with the android.intent.action.VIEW action and startActivity() . Intent intent = new Intent(Intent.ACTION_VIEW); // Choose a value for uri from the following. // Search Google Maps: geo:0,0?q=query // Show contacts: content://contacts/people // Show a URL: http://www.google.com intent.setData(Uri.parse(uri)); intent.setFlags(Intent.FLAG_ACTIVITY_NEW_TASK); startActivity(intent); Other useful action/URI pairs include: Intent.ACTION_DIAL , tel://867530
Read more