Skip to main content

Scooba Stuck In Diagnostic Mode

This morning, I turned on my Scooba and it started beeping a scale of tones and blinking all its lights in sequence. After an hour or so of resetting, cleaning, disassembling, researching, and scratching my head, I stumbled across the solution on Roomba Review. But, for me at least, it was even easier than all of that. I don't have any of my own pictures for this procedure, but it's pretty straight forward.
  • Remove the battery and power.
  • Remove the two screws holding the bumper shell in place and remove it.
  • Carefully peel up the sticker with the control buttons on it. This sticker is actually the control panel. There is a data cable attached to it just below the "Clean" button. Be careful not to break it!
  • Clean the surface under the sticker with some isopropyl alcohol. (I didn't actually have to do this, but I'm sure it doesn't hurt.)
  • Gently replace the "sticker" (i.e. control panel) and make sure it's completely flat.
  • Check to see if it works again. If not, repeat.
  • Replace the bumper shell and screws.
It turns out that this "unfixable" (according to iRobot) problem is usually just some moisture under the contacts in the control panel.
Labels:

Popular posts from this blog

Email Injection

Not so long ago, I ran a wiki called SecurePHP. On that wiki, there was one particular article about email injection that received a lot of attention. Naturally, with all the attention came lots of spam. As a result, I disabled editing of the wiki and content stagnated. Still, the email injection article remained popular. About a year later, the server that hosted SecurePHP died and I never had a chance to hook it all back up. I saved the article though and I'm reposting it now. It may be a bit old (I've been away from PHP for a long time), and I didn't write all of it, so feel free to leave comments about needed updates and corrections. Though this article focuses on PHP, it provides a lot of general information regarding email injection attacks. The PHP mail() Function There are a lot of ways to send anonymous emails, some use it to mass mail, some use it to spoof identity, and some (a few) use it to send email anonymously. Usually a web mailform using the mail() funct
Read more

XBee ZNet 2.5 Wireless Accelerometer

I managed to put together a wireless accelerometer the other night using my two new XBees, an Arduino XBee shield, an XBee Explorer USB, an ADXL330, and some Python. I struggled a bit with some of it, so here's what I learned: First, a parts list. XBee 2mW Series 2.5 Chip Antenna Arduino XBee (with XBee Series 2.5 module) XBee Explorer USB ADXL330 I'm not sure exactly what the specs are on the XBee that comes with the Arduino shield. But, it is definitely a series 2.5. The first thing to do is to configure and upgrade the firmware on your XBees. To do that, you'll need X-CTU (for the firmware upgrade at least, but it's also nice for configuration) which, unfortunately, is only available for Windows. But, it works fine from VMware. First up, the XBee we'll hook up to the computer to read incoming data from the accelerometer: Plug one of the XBees into the Explorer (it's also possible to do this from the Arduino shield by shifting the two XBee/USB jumpers to USB
Read more

Android Recipes and Snippets

I've put together a small collection of Android recipes. For each of these recipes, this is an instance of Context (more specifically, Activity or Service ) unless otherwise noted. Enjoy :) Intents One of the coolest things about Android is Intents . The two most common uses of Intents are starting an Activity (open an email, contact, etc.) and starting an Activity for a result (scan a barcode, take a picture to attach to an email, etc.). Intents are specified primarily using action strings and URIs. Here are some things you can do with the android.intent.action.VIEW action and startActivity() . Intent intent = new Intent(Intent.ACTION_VIEW); // Choose a value for uri from the following. // Search Google Maps: geo:0,0?q=query // Show contacts: content://contacts/people // Show a URL: http://www.google.com intent.setData(Uri.parse(uri)); intent.setFlags(Intent.FLAG_ACTIVITY_NEW_TASK); startActivity(intent); Other useful action/URI pairs include: Intent.ACTION_DIAL , tel://867530
Read more